Pluto+ 70MHz~6GHZ AD9363 SDR Radio Receiver Transmitter 2xRX 2xTX Compatible with ADI ADALM-PLUTO PLUTO+
Direct purchase from the factory 
Tabbacin Biyan Kuɗi lafiya
Kyauta Kyauta
Manufar Jigilar Kaya
Manufar KomawaKyauta Kyauta
Barka da zuwa Roymall, shafinku na siyan kyaututtuka masu inganci. Muna girmama goyon bayanku, kuma muna ba da kyauta kyauta tare da kowane siyayya. Shirya don bincika tarinmu kuma ku sami kyaututtukanku masu dacewa.Manufar Jigilar Kaya
Za mu aika kayanku cikin kwanaki 2 bayan siyayya.Lokacin jigilar kaya yawanci kwanaki 5-7 ne.Saboda jigilar mu ta duniya ne, lokacin jigilar zai dogara da wurin ku.1. Manufar Komawa
Muna karɓar abubuwan da aka saya daga roymall.com kawai. Ba za a iya mayar da kyauta kyauta ba. Dole ne abu ya kasance ba a yi amfani da shi ba kuma a cikin yanayin da kuka karɓa.Za mu sarrafa komawar ku cikin kwanaki 3-5 bayan karɓa.Ba za a iya mayar da abubuwan da aka keɓance ba.Tuntuɓi mu. service@roymall.com ko Whatsapp: +86193598494712.Manufar Maida Kuɗi
Za ku sami cikakken maida kuɗi bayan mu karɓi abubuwan da aka dawo. Kuɗin jigilar kaya ba za a iya mayar da su ba.Tuntuɓi mu. service@roymall.com ko Whatsapp: +8619359849471https://drive.google.com/file/d/1OnJOtojzaN82d3yuHzG1YkfeXNFKKYbA/view
https://github.com/plutoplus/plutoplus/releases
Description:
Pluto+ is a software-defined radio platform that supports 2TX 2RX, supports Gigabit Ethernet and Micro SD card. The design draws on the well-known ADI ADALM-PLUTO and improves its shortcomings.
Features:
1. ADC/DAC: AD9363(Can hack to AD9361 or AD9364)
2. 2 Transmit, 2 Receive channel
3. RF Range: 70MHZ~6GHZ
4. Ref Clock: VCTCXO 40MHZ0.5ppm
5. SOC: Zynq7010 FPGA: 28K
6. RAM: 512M
7. FLASH: 32M
8. USB: 2.0support OTG
9. Ethernet: 1000Mb
10. Micro SD can use to boot
11. DC IN: 5V u00b10.5V-2AmicroUSB
Package Include:
1 x Pluto+ Software Radio
2 x Cable
Interface:
Please note that all IO levels are 1.8V.
3.1 When using the official ADI-PlutoSDR firmware, please connect to URST-MI052.
3.2 When using Pluto+ firmware and need to support Ethernet, please connect URST-MIO46
3.3 When using SD card to boot, please connect SD-H to 1V8
3.4 When using JTAG to debug, please connect JTAG# to GND
3.5 Please connect EXCLK to GND when using external reference clock input
PTT key port
PTT drives optocouplers through GPIO0 (MI00), which requires an external relay or control circuit.
DFU KEY
At any time, you can press the DFU button and power on PLUTO+ again to enter the DFU mode, but you need to connect the URST jumper to MI052
Ref CLK input IPEX
You can connect a cable to input an external high-precision reference clock for AD9363 through the IPEX interface.
The main level should not exceed 3.3V, and the EXCLK jumper needs to be connected to GND to turn off the built-in clock
Calibrate the frequency of the built-in VCTCXO
The frequency of the 40M clock can be fine-tuned by adjusting the adjustable resistor next to the VCTCXO, provided that you have a reference signal source
Micro-SD
Support booting via SD card, need to connect SD-H jumper to 1V8
